Rake board
The trim board up the sloped side of a gable. Barge board is another name for it.
Free 3D design for any room in your home, siding or roof, before you sign · 10% off for veterans and seniorsFree 3D design · 10% off for veterans and seniors
Roof edge · Elk Grove
A rake board, also called a barge board, is the trim board that runs up the sloped edge of a gable roof, from the eave to the peak. In Elk Grove we replaced two rake boards on a tile roof for a signed $3,672 in one day, seven days before the contract’s target finish date; we always apply for the permit ourselves.
We reset the tiles and painted the new boards on October 13, 2026. Below: why rake boards rot, what our two roof edge jobs cost, and what to ask before the work.

The trim board up the sloped side of a gable. Barge board is another name for it.
It sits at the roof edge, where water runs past it every rain.
$3,672 in Elk Grove on a tile roof; $3,350 in Sacramento with fascia and edge flashing.
Gable edge
A rake board is the trim board that runs up the sloped edge of a gable. Barge board and verge board are other names for it. The drawings show where each part sits.

Covers the end of the roof framing along the sloped gable edge.

The board along the bottom, level edge, where the gutter hangs. It meets the rake board at the corner; see our fascia guide.

On a shingle roof, the code requires a drip edge along the rake too, with the underlayment under it; see what a drip edge is.

Why it rots
They sit right at the roof edge, so every rain runs past them. Check them from the ground, not from a ladder. The drawings show where the water gets in.

Rain runs along the roof edge and over the end grain at the corners.

Once paint peels or a joint opens, water can soak in and stay.

Water can run behind a badly installed metal edge and into the board.
Our job
The homeowner needed the roof done before a home sale closed. We signed on October 6, 2026, at $3,672, and the final invoice was the same, with no change orders. More about our work in Elk Grove and on our roofing page.
Both deteriorated boards off, new boards on, primed and finished with the homeowner’s exterior paint.
The tiles in the work area came off, and serviceable existing tiles went back on.
The exposed underlayment was repaired before the tiles were reset.
The local flashing and the upper tile joint were repaired and sealed.


See every before and after photo from the Elk Grove job.
See the Elk Grove projectGet my free estimateShingle roofs
On a shingle roof the first shingles are opened instead of lifting tiles.
One rake board with the fascia and metal edge was a signed $3,350; see what that repair included.

Cost
Our two roof edge jobs show what moves the number.
On a tile roof the edge tiles come off and go back, as in Elk Grove. On shingles, the first shingles are opened and put back.
Rot in the rafter or the roof deck behind it adds work. You get a written price before that work.
Our Sacramento price included new edge flashing, which helps keep the new board dry.
Our Elk Grove price included painting the new boards. Ask whether paint is in yours.
About the author
Our Chief Designer wrote this guide and our general contractor reviewed it.
Chief Designer
Emin is the Chief Designer at US Construction Remodeling Corp. Emin leads client design meetings, measured layouts and 3D visualization in Revit, 3ds Max and Unreal Engine, and uses AI tools to speed up design and project planning.
General Contractor
Umit Sahin is a general contractor at US Construction Remodeling Corp. and oversees construction, permits and inspections on our projects.
Sources
The state roof code and our license record.
R905.2.8.5: drip edge at the eaves and rake edges of a shingle roof.
Where the California building codes are published.
California contractor license #1117562 on the state license board.
Plan the numbers
If the edge is only part of it, measure the whole roof first.
Outline your roof on a map, or work out shingles and underlayment.
Roof calculatorShingle and underlayment calculatorGet my free estimatePractical questions
Short answers about names, cost, time and permits.
The trim board that runs up the sloped edge of a gable roof, from the eave to the peak.
Yes. Barge board, verge board and rake board are names for the same board on the gable edge.
Fascia runs along the bottom, level edge of the roof, where the gutter hangs. The rake board runs up the sloped side.
In Elk Grove, two rake boards on a tile roof, with the tiles reset and the boards painted, were a signed $3,672. In Sacramento, one rake board with the fascia and edge flashing was a signed $3,350.
Both of our jobs took one day on site.
We check your address with the City and always apply for the permit ourselves.
Plan your project
Send your address and a few photos. We look for free, tell you whether a repair is enough, and send a written price before any work starts.
US Construction Remodeling Corp. · CSLB #1117562 · 4424 Freeport Blvd. STE 4, Sacramento, CA 95822
Keep planning
Our roofing service, two roof edge jobs and two more roof edge guides.