What it is
The board along the bottom edge of the roof, where the gutter hangs.
Free 3D design for any room in your home, siding or roof, before you sign · 10% off for veterans and seniorsFree 3D design · 10% off for veterans and seniors
Roof edge · Sacramento
Fascia is the trim board along the lower edge of the roof that covers the rafter ends and holds the gutter. On a Sacramento garage we replaced the rotted fascia, a rake board and the metal edge for a signed $3,350 in one day, October 28, 2026; we always apply for the permit ourselves.
Below: how to tell fascia needs work, what our job included, and what changes the price.

The board along the bottom edge of the roof, where the gutter hangs.
$3,350 for the fascia, one rake board and the metal edge on one garage, in one day.
New boards can rot again if the metal edge above them lets water behind.
Roof edge
Fascia is the trim board along the lower edge of the roof. It covers the ends of the rafters, and the gutter hangs on it. The drawings show where each part sits.

Runs along the bottom edge of the roof, where the gutter is attached.

Runs up the sloped side of a gable. Some call it a barge board; see our rake board guide.

The flat panel under the roof overhang, between the fascia and the wall.

The metal strip over the top of the fascia that drips roof water into the gutter; see what a drip edge is.

Signs
Look from the ground, not from a ladder. Rot tends to start where water sits: at the corners, at joints and behind a loose metal edge. The drawings show what each sign looks like.

Boards that look split, swollen or dark can mean rot. We check the wood up close when we look at your roof.

Peeling or dark stains in one spot can mean water is getting into the board.

The gutter hangs on the fascia, so a loose gutter can mean weak wood behind it.

On our Sacramento garage, the metal edge was not installed right, so water got behind it and rotted the fascia and a rake board.
Our job
The homeowner called about a damaged corner of the garage roof before the winter rains. We looked the same day, sent a written estimate, and did the repair in one day. More of our work around Sacramento and on our roofing page.
We took off the rotted boards and the old metal edge, then checked the wood behind them.
New primed boards, sized to match, fastened to solid wood. The estimate priced up to 16 feet of fascia and one rake board up to 16 feet long.
About 32 feet of new metal edge flashing, worked in with the shingles and the underlayment so water runs into the gutter.
The gutter was in good shape, so we protected it and kept it.
We put back the shingles we had opened and hauled away the old wood.


See every photo and the short video from the repair day.
See the Sacramento projectGet my free estimateCost
Two of our roof edge jobs, both signed prices, show what moves the number.
Our Sacramento job was one garage edge and one gable side. A whole house edge is many times longer.
Rotted rafter ends or roof deck add work. We show you and give a written price before doing more.
If the flashing above the fascia is wrong, a new board can rot again. Our price included new edge flashing.
In Elk Grove, two rake boards on a tile roof, with the tiles lifted and reset and the boards painted, were a signed $3,672. See the Elk Grove job.
About the author
Our Chief Designer wrote this guide and our general contractor reviewed it.
Chief Designer
Emin is the Chief Designer at US Construction Remodeling Corp. Emin leads client design meetings, measured layouts and 3D visualization in Revit, 3ds Max and Unreal Engine, and uses AI tools to speed up design and project planning.
General Contractor
Umit Sahin is a general contractor at US Construction Remodeling Corp. and oversees construction, permits and inspections on our projects.
Sources
The state roof code, the City’s permit list and our license record.
R905.2.8.5: the metal drip edge at the eaves and rakes of a shingle roof.
Which work the City of Sacramento lists as needing a permit.
Where the California building codes are published.
California contractor license #1117562 on the state license board.
Plan the numbers
If the edge is only part of it, measure the whole roof first.
Outline your roof on a map, or work out shingles and underlayment.
Roof calculatorShingle and underlayment calculatorGet my free estimatePractical questions
Short answers about cost, soffits, gutters and permits.
Our Sacramento garage repair was a signed $3,350 for the fascia, one rake board and the metal edge flashing. Your price depends on the length, the wood behind the boards and the flashing.
Fascia is the upright board along the roof edge, where the gutter hangs. Soffit is the flat panel under the overhang.
Fascia runs along the bottom edge of the roof, where the gutter is attached. A rake board runs along the sloped side edge of a gable.
The gutter hangs on the fascia, so it has to be handled. On our job the gutter was in good shape, so we protected it and kept it.
Ours took one day. More damage behind the boards takes longer, and you get a written price before that work.
We check your address with the City and always apply for the permit ourselves.
Plan your project
Send your address and a few photos of the roof edge. We look for free, tell you whether a repair is enough, and send a written price before any work starts.
US Construction Remodeling Corp. · CSLB #1117562 · 4424 Freeport Blvd. STE 4, Sacramento, CA 95822
Keep planning
Our roofing service, two roof edge jobs, gutters and the roof cost guide.